Harsh Front-End Gladiator Tipping Gear (PGT32): -

Lower weights of tipping gears means more load, more loads means higher earnings, higher earnings means more profit. A Harsh Front End Gladiator Tipping Gear (PGT32) is the lightest tipping gear available on the market today. The total ‘wet’ weight is 543kgs for an 8x4 tipper. It uses the tough and long lasting one-piece tube design, large overlaps and minimum running clearances between tube stages to give excellent rigidity. This allows less oil, less weight and optimum tipping cycles.

PGT32 Gladiator Weights
Tipping Gear Make
 HARSH
Tipping Gear Model
 PGT (PFT 4/135/5070)
Truck
 Model WB Gear Box
Volvo 8x4 Day Cab 5100
Component
 Unit Dry Weight kgs Unit Wet Weight Kgs Qty Total Wet Weight Kgs
Ram And Tank
 315.5 366 1 366
Oil in Annuli & ath Stage
   4 4.36 Litres 4
Hydraulic Control Valve
 3.5 3.5 1 3.5
Air Control Valave c/w Kit
 1 1 1 1
PTO
 6.5 6.5 1 6.5
Pump
 14 14 1 14
Pipe Adaptor Kit
 3 3 1 3
Lifting Brackets
 10 10 1 20
Pedestal Brackets
 19 19 2 38
Pedestal Gussetts
 0.5 0.5 4 2
Cradle Brackets
 5.25 5.25 2 10.5
Low Pressure Pipe
 2 2 1 2
High Pressure Pipe
 2 2 1 2
Hinge Bar
 24 24 1 24
R-Hinge Body Brackets
 16.25 16.25 2 32.5
R-Hinge Chassis Brackets
 5.25 5.25 2 10.5
Hinge Collar/Bosses Kit
 1.5 1.5 1 1.5
Bolt Kit - Pipe Clips
 2 2 1 2
Ram & Tank Wet Weight Without Valave
       370
Ram & Tank Wet Weight With Valave
       373.5
Total Full Kit Weight
       543

Note:(1) The above data are actual weights recorded on 25 April 2006 using certified digital Salter scales. (2) The weight of oil in the annuli and small inner are calculated. (Calculation available)

The Gladiator ram and tank represents the perfect answer for profitable tipping on 6x4 and 8x4 tipper vehicles.

Harsh Stabilised Underfloor Tipping Gear (K110N): -

The Harsh K110N model is an impressive 76kgs lighter than the competition and even lighter than some Front End Ram manufacturers. Dispelling the common ‘myth’ that Front End tipping gears are always lighter than Underfloor tipping gears.

The Harsh Underfloor Stabilised K110N Tipping Gear for an 8x4 Tipper weighs 649.5kgs including Oil.

Harsh Slide ‘N’ Cover Sheeting Systems: -

The Harsh Slide ‘N’ Cover is one of the lightest sheeting systems available in the market. All components are made from galvanised steel, aluminium or zinc plated for rust protection and better appearance. The Slide ‘N’ Cover is built to the lightest possible weight whilst never compromising on quality or strength.

Compare your existing sheeting system against our chart below to see how much more money you could make from our lightweight design.

Harsh Slide N Cover Electric Operation 83.5kgs 93.0kgs 101.5kgs 141.0kgs
Harsh Slide N Cover Manual Operation 65.0kgs 77.0kgs 84.0kgs 117.0kgs
STD Side 2 Side System Manual Operation 117.0kgs 136.0kgs 159.0kgs 205.5kgs
STD Side 2 Side System Automated Operation 220.0kgs 260.0kgs 280.0kgs 400.0kgs
© Harsh UK 2009